 SAE Direct Drive PTO | John Deere 4045T
Logan Front Mount PTO’s for John Deere 4045T Diesel Engines and Generator Sets
|
Features:
-
Air or Fluid Actuated from 80 to 100 psi.
-
25% more torque (520 lb. ft.) and higher engagement speeds (1800 RPM).
-
The low profile, compact, Logan PTO design is suitable for workboats, fishing boats and pleasure craft.
-
The Logan PTO aids in the reduction of emissions, energy, fuel costs and wear and tear on auxiliary attachments.
-
Field retrofits with existing John Deere / Pitts Style electromagnetic PTO clutches.
-
Also available for 6068, 6081, 6090 and 6135 models (75-600 HP / 56-448 KW).
|
|
404 lb. ft. of torque @ 80 psi. / 520 lb. ft. @ 100 psi. Max engage- ment speed is 1800 RPM. Clutch shown with cover plate removed.
|
Advantages:
-
During maneuvering–which requires reduction of main engine speed, the Logan PTO is used as a separate power source for bow and stern thrusters.
-
The PTO directly connects to a pump drive, which powers winches, reels, hoists, and deck pressure washers.
-
The PTO can be coupled to an alternator to supply electric power to other power consumers on the vessel.
|
|
Air/Fluid Actuated PTO SPF 400 Specifications
|
|
|
|
Dimensions
|
|
A |
8.99 in
228.3 mm |
F |
1.63 in
41.4 mm |
|
B |
6.65 in
168.9 mm |
G |
0.28 in
7.1 mm |
|
C |
5.81 in
147.6 mm |
H |
3/8-16 |
|
D
|
7.59 in
192.8 mm |
J
|
6.25 in
158.8 mm |
|
E |
5.00 in
127.0 mm |
K
|
7.95 in
201.9 mm |
|
PTO SPF 400 Specifications
|
|
|
U.S
|
S.I.
|
|
*Rated Torque (Maximum)
|
400 Ft/Lbs
|
524 Nm
|
|
Maximum HP
|
180 HP
|
134 KW
|
|
*Maximum RPM
|
2400 RPM
|
2400 RPM
|
|
**Maximum Engagement RPM
|
1800 RPM
|
1800 RPM
|
|
Rotation
|
Bi-rotation
|
Bi-rotation
|
|
Maximum Actuation Pressure
|
100 psi
|
6.9 Bar
|
|
Displacement (Maximum)
|
4.5 in3
|
74 cm3
|
|
Minimum Flow Rate Required
|
1.5 GPM
|
5.6 Liters/min
|
|
Operating Media at Clutch (Oil or Air)
|
Standard
|
Standard
|
|
Maximum Back Pressure to Tank
|
7 psi
|
0.5 Bar
|
Maximum Fluid Temperature
|
180º F
|
82º C
|
|
Material - Output Hub
|
Alloy Steel
|
Alloy Steel
|
|
Material - Housing
|
Aluminum
|
Aluminum
|
|
External Finish - Output Hub
|
Alloy Steel
|
Alloy Steel
|
|
External Finish - Housing
|
Aluminum
|
Aluminum
|
|
Weight (Approximate)
|
29 Lbs
|
13 Kg
|
* Consult Logan Clutch for applications that require lower actuation pressure or increased torque and rpm requirements or greater installation angle.
** Soft start feature may be required for engagement above machine idle rpm.
* Input drive flange bolt pattern are dimensioned to correlate with Lovejoy or Centa torsional coupling size 50.
|
Note: The torque capacity of the clutch is directly proportional to the operating pressure. Maintaining the lowest pressure possible to transfer the desired torque will enable the clutch to run cooler and extend the life span of the internal bearings.
The output end of the clutch (female spline/bore) is not capable of supporting any side load. Use overhung load adapters.Drive shaft alignment must be within 3 degrees. Maximum installation angle should be 7°.
|
PTO SPF 400 Series Static Torque Ratings
|
|
PSI (Ratings in ft. lbs.)
|
Model
SPF 400
|
80
|
90
|
100
|
|
404
|
462
|
520
|
|
PTO SPF 400 Series Static Torque Ratings
|
|
BAR (Ratings in Nm)
|
Model
SPF 400
|
5.5 |
6.2 |
6.9 |
|
548
|
626
|
705
|
|
Horsepower Required to Drive Hydraulic Pump
|
HP*
|
25 |
50 |
100 |
|
Pump Size(GPM)
|
20
|
40
|
80
|
*HP=PSI x GPM/1371.2 (1714x80% efficiency=1371.2)
*1 HP is required for each 1 GPM@1500 PSI
|
PTO SPF 400 Series Pump Shaft Options
|
Output Description
|
|
SAE 'C' Spline 14t 12/24 DP |
|
SAE 'B' Straight Shaft 1.250 Dia. with 5/16 Key |
|
Shaft 1.250 Dia. with 5/16 Key |
|
|
